BS EN 10264-1-2002 钢丝和钢丝产品.绳索用钢丝.一般要求
时间:2024-05-23 16:13:53 来源: 标准资料网 作者：标准资料网 阅读：8374
【英文标准名称】:Steelwireandwireproducts-Steelwireforropes-Generalrequirements
【原文标准名称】:钢丝和钢丝产品.绳索用钢丝.一般要求
【标准号】:BSEN10264-1-2002
【标准状态】:作废
【国别】:英国
【发布日期】:2002-04-18
【实施或试行日期】:2002-04-18
【发布单位】:英国标准学会(GB-BSI)
【起草单位】:BSI
【标准类型】:()
【标准水平】:()
【中文主题词】:材料强度;抽样方法;钢产品;尺寸;防腐蚀;金属线;绳索;钢丝;验收(鉴定);圆形;尺寸公差;机械性能;作标记;名称与符号;金属丝绳;钢丝绳;化学成分;覆层;抗拉强度;认证;圈数;公差(测量);规范(验收);定义;交变弯曲值;圆度;质量(物质);钢;一般条件;直径
【英文主题词】:Acceptance(approval);Certification;Chemicalcomposition;Circularshape;Coatings;Corrosionprotection;Definition;Definitions;Designations;Diameter;Dimensionaltolerances;Dimensions;Generalconditions;Marking;Mass;Mechanicalproperties;Numberofalternatebends;Numberofturns;Ropes;Roundness;Samplingmethods;Specification(approval);Steelproducts;Steelwires;Steels;Steel-wireropes;Strengthofmaterials;Tensilestrength;Tolerances(measurement);Wireropes;Wires
【摘要】:ThispartofthisEuropeanStandarddefinesthegeneralrequirementsforwireintendedformechanicalropes.Additionalrequirementsaregiveninthefollowingpartsofthisstandard,whicharespecifictoeachcategoryofwire.Thisstandardspecifies—dimensionaltolerances—mechanicalcharacteristics—requirementsrelatingtothechemicalcompositionofthesteelwire—conditionstobesatisfiedbyanycoating.
【中国标准分类号】:H49
【国际标准分类号】:77_140_65
【页数】:14P.;A4
【正文语种】:英语
Product Code:SAE AS85049/15
Title:Connector, Accessories, Electrical, Strain Relief, 45掳, Non-Self-Locking and Self-Locking, Category 4C (For MIL-DTL-38999 Series III and IV Connectors)
Issuing Committee:Ae-8c1 Connectors Committee
Scope:No scope available.Product Code:SAE ARP4296
Title:Drawing Interpretations and Standard Machining Practices, Couplings, Fittings and Hose Ends, Fluid Systems
Issuing Committee:G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
Scope: This SAE Aerospace Recommended Practice (ARP) is intended to interpret and clarify engineering drawing requirements relating to the manufacture and inspection of fluid tube fittings and connectors. Because it is impractical to define every minute detail of the parton the face of the drawing, this document describes general machining tolerances that fall under the heading of, 'good shop practice'. This document serves as a supplement to engineering drawings when referenced on applicable documents.
Rationale: This SAE Aerospace Recommended Practice (ARP) is intended to interpret and clarify engineering drawing requirements relating to the manufacture and inspection of fluid tube fittings and connectors. Because it is impractical to define every minute detail of the parton the face of the drawing, this document describes general machining tolerances that fall under the heading of, 'good shop practice'. This document serves as a supplement to engineering drawings when referenced on applicable documents.